Micro draco red dot

This is a question that pops up now and then and has been debated on many a gun forum. Besides the obvious answer, on the top of the rifle, there are a few things to consider. People will adamantly claim one way is better than the other, but at the end of the day do what works best for you.

Posts navigation

Mounting optics to fixed carry handles was cool in the 90s. We have better systems now. While it may be tough to figure out exactly where you want to mount your RDS, it is very easy to decide where NOT to mount it. Even if you have a free floated handguard, it will never be as consistent and solid as mounting it on the top of the receiver.

micro draco red dot

Your weapon heats up as you shoot — and the most heat is in the chamber and barrel, which is surrounded by your handguard. Metal expands when heated, and depending on how your handguard attaches to your gun, your zero can, and likely will shift to some degree.

How much is impossible to tell. Some manufacturers have begun to design handguards to mount in such a way to minimize this, like the BCM KMR, but as a rule of thumb, keep your RDS on the top of your receiver. The exception may be with some of the monolythic uppers where the handguard and upper receiver is one solid piece.

So, in conclusion — where should you mount your RDS? I generally find most people do best with it somewhere in the middle of the receiver or farther forward. You can also try shooting some groups in the two different positions and see if you notice any difference. At the end of the day, like many things with gear setup and shooting, a lot of it comes down to personal preference. When you decide where you like it, take a silver Sharpie and make a little mark from the mount to the receiver, so if you remove it, you can get it back to the same spot.

Learn your system, and if you have to, double check your zero. This is especially important in rifles where a high-degree of accuracy is expected. Nice article fellas. Keep up the good work, be safe. I enjoyed your article. I find the best position for an EOTech on a non-traditional rifle like the Kel-Tec SUB that does not have a Picatinny rail over the receiver is to mount the optic all the way out front on the hand guard.

Save my name, email, and website in this browser for the next time I comment. Notify me of follow-up comments by email. Notify me of new posts by email. Like this: Like Loading I realize the SUB be the go-to rifle for the professional gunfighter, but they are popular.

Leave a Reply Cancel reply Your email address will not be published.Buy Together and Save. Please click here for more information. This should fit, however do to the wide array of AK variants on the market, there is always the possibility that some minor fitment could be required.

Please enable JavaScript in Your Browser JavaScript is not currently enabled in your browser and due to this our site will not work as it should.

While JavaScript is disabled, you will not be able to add items to your cart or browse all product options. Our site is powered by industry leading security standards for your protection. If possible, please enable JavaScript in your browser for the best possible experience. If you cannot enable JavaScript or you are having technical difficulties, please contact us — we are always here to help!

Please Enable Your Browser's Cookies Functionality Cookies are not currently enabled in your browser, and due to this the functionality of our site will be severely restricted. Web browser based cookies allow us to customize our site for you, save items in your cart, and provide you with a great experience when shopping OpticsPlanet.

Your privacy is important to us, and any personal information you supply to us is kept strictly confidential.

micro draco red dot

If you cannot enable cookies in your browser, please contact us — we are always here to help! Unfortunately we are unable to offer our excellent shopping experience without JavaScript.

Please add " opticsplanet. Add To Cart. Click to select this item for your bundle offer! Select a specific model above to see the deal! Replaces existing AK receiver cover. Tap Tap to Zoom. You May Also Like. I have a Chinese sks, will this fit my rifle? Expert Answer This should fit, however do to the wide array of AK variants on the market, there is always the possibility that some minor fitment could be required.

Customer Reviews. I had to spend too much time trying to get it to fit and haven't actually reached fit yet. I don't know why they can't make it correctly.

This item does not fit dracos. You cant adjust it or work on it to make it fit. I got it thinking I could get out of changing the hand guard. Needless to say i had to end uup buying a hand guard from mag pul i believe. I bought this item over a year ago, I should of asked for a refund but when I called it was too late.

I've spend too much time trying to get it to fit but there's no way that's Read More Most Recent Reviews Doesn't fit. RMA Still waiting for refund after returning it. Purchase done one month ago.Discussion in ' Firearms ' started by alnenAug 26, Log in or Sign up.

AK Pistol? Want to mount a Red Dot? Look no further! Aug 26, 1. I was forunate enough to test this product out on my Zastava M92 AK pistol, and am extremely happy with the results. I searched high and low for a good option to mount an optic to my ak pistol in a sturdy way, and I finally found it. Installation was fairly simple, and this upgrade really performs on the range! First I'll give a range review, then I'll give you installation instructions. It does come with instructions when it arrives, but I break it down step by step to save you a little time.

Very affordable, and I believe it to be the best bang for the buck. I also installed a Magpul MOE cantilever rail section on the bottom of the handguard so I could attach a light. You have to install the rail segment before you install the forend on your gun, so do that first so you don't have to take the forend off in the future.

I ordered my top plate to use with the Aimpoint micro. You don't need any kind of additional mount with it, the top plate attaches directly to the RDS.

The handguard is comfortable in the hand, and allows alot of mounting options. It did withstand my brute prying very well, which is impressive, because I usually break things! With this being a pistol, your mounting area is obviously very limited. I searched for a good flashlight option, and my best solution was to install the cantilever rail section all the way forward with the TLR3 pistol light lumens, very small. This allows me to fully utilize my handguard and still have lighting. At the range, the forend performed well.

I had zero issues. I sighted in my red dot at 25y, 50y, and y. I adjusted my aimpoint 35 clicks up in elevation and NONE for windage.We offer sales and consignments of firearms and class III weapons as well as components. Please be aware that we cannot sell products that may be in violation to your states rules and regulations regarding firearms, magazines and other related products. Please contact us if you have questions regarding legalities in your state.

All rear stock adapters in the Draco section fit all Draco pistols, mini and micro as well. Instructions included with rear adapters. Our new Buffer Tube Threaded stock adapter makes it easy to add an AR stock to your Draco using our adapter between the grip and the receiver. Any buffer tube type AR stock will thread into the adapter, both commercial and Mil spec can be used. Please call with any questions. This part number for the Adapter only, other parts sold separately.

We include two grip bolts for use with the OEM grip and most aftermarket grips. Also fits Mini Draco.

Micro Draco AK47 pistol Valken Upgrade Installation Review

Brace for the AK47 Draco. We provide 2 longer bolts to use your OEM grip and most aftermarket grips. Fits all Draco models, mini and micro as well. Upgraded folding adapter offers upgraded machined parts, machined improved locking buffer tube slot to prevent turning, upgraded stiffer hinge spring, improved, wiggle free locking hinge, slimmer design and harder coating. Also fits Mini Draco and Micro. Mounting instructions included, no drilling or welding.

Fits ALL Draco pistols only. Upgraded folding adapter offers upgraded machined parts, machined improved locking buffer tube slot to prevent turning, upgraded hinge spring, improved locking hinge, slimmer design and harder coating. Locks open and locks when closed. Upgraded folding adapter offers upgraded machined parts, machined improved locking buffer tube slot to prevent turning, upgraded hinge spring, improved, wiggle.

Our new double sling loop offers a bit longer sling more accessible loop. Fits most AR type buffer tubes for Braces and Blades. It allows a sling to be attached at either the left or right side of the rear of the receiver. Our new type rail adapter makes it easy to add a sling or other rail mount attachment to your AK Draco Pistol using our adapter between the grip and the receiver.

The Rear Rail can also be removed to use the adapter and mount a flat mount stock as well. This part number for the Adapter with small machined aluminum rail only. Adapter and rail both made of machine series aluminum. Our AR stock adapter paired up with a 7. Upgraded folding adapter offers upgraded machined parts, machined improved locking buffer tube slot to prevent turning, upgraded hinge spring, improved, wiggle free locking hinge, slimmer design and harder coating.

Tactical stock features 6 QD swivel points, 1 QD swivel included.Remember Me? Page 1 of 2 1 2 Last Jump to page: Results 1 to 10 of Thread: Draco AK Pistol mount and red dot. Thread Tools Show Printable Version.

micro draco red dot

I am considering adding a red dot. I like the strike industries rear sight mount and one of the primary arms micro red dots. Would this be a good combo? Any other inexpensive suggestions? I saw the strike industries a friend had and preferred the design or the attero arms mount and primary arms micro, I have that is on my mini draco, on my standard draco I have a parabellum armament akars dust cover rail and Bushnell TRS On a side not the hooded Front sight will mess with your sight picture through the optic, I have been thinking about trimming the hoods on them.

I may go with the bushnell red dot. I want to be able to cowitness the sights to.

I like the Ultimak rail, but am looking into others also. Which mounts can I still use the sights with? I used a Sparc with the riser.

I replaced the wood furniture with a Midwest Industries Quad Rail. The Sparc comes with the riser. Attached Images.

AK Pistol? Want to mount a Red Dot? Look no further!

I'm thinking an Ultimak may be my best bet Still need to test it at the range Page 1 of 2 1 2 Last Jump to page:. Clair County St.

All times are GMT The time now is PM. All rights reserved.Are you a shooting enthusiast? If yes, then you know that shooting a firearm without a sight is definitely a heartbreak in waiting. See what will happen, on top of missing the target, you also give it the opportunity to escape or react. For this reason, having a sight is a wise decision as it allows you to accurately hit your target. Together with this is an in-depth buying guide, to help you make an informed buy decision.

So you are welcome…. To start with, the Paralow Red Dot Sight comes with a very powerful battery which can provide up to 50, hours of continuous usage. Another cool thing is that there is an automatic switch that will automatically light up when it senses movements and shut off after a default period. In addition to this, the battery housing has been designed on the right side of the optic to provide you with easy access to the battery.

This allows for quick and easy change. One thing that I liked most is the fact that I can enjoy my hobby even when darkness comes as the sight is designed for day use and night vision. With a durable and reliable construction, it means you can take your unit to any weather with no fears of damage. It is interesting to note that this sight is unaffected by extreme weather.

The good news is that it comes with a complete waterproofing another plus especially when you are taking this scope to marshy grounds. Our Rating: 4. If you are a shooting pro looking for a split-second target acquisition, you might find the Vortex sight very useful.

micro draco red dot

It is designed for shooters looking for accuracy and lightning speed in mind. Featuring unlimited field of view, unlimited eye relief, and the parallax-free design allows you to shoot rapidly with both eyes open.

The red dot aligns properly to the target quickly, saving your eyes from serious strains. It is interesting to see that the bright red dot comes with 10 brightness settings so you can choose the ideal one for you. And the included 2-night vision settings allows for night operation. If you love long shooting adventures, the battery coming with this scope is going to provide you with hours of use.

As for durability, the Vortex sight comes with an anodized finish. Another interesting thing is that it is waterproof and fog proof. If you are looking for an easy to set up Red Dot Sight for your weapon, then you may want to consider this EOTech sight.

Designed for first time users in mind, this EOTech sight is easy to mount on any rifle and get the job done. With a single-lithium battery configuration, the OETech sight has more space than ever for rear iron sights and magnifiers. In terms of power, this red-dot sight features an improved battery life compared to previous models. This Holographic Weapon sight comes with a sturdy and reliable construction which gives it the ability to function in the most demanding conditions.

It is also proven to be waterproof and submersible into the water to depths of 10 meters. Furthermore, the holographic sighting technology gives you unlimited field of view. You can also, shoot with both eyes open for fast target acquisition. Unlike other models, this riflescope features a multi-coated optics that helps hunters to quickly distinguish between targets from elements.

This means that you would have no problem aiming their target in low-light conditions. This means it is going to provide you maximum performance even in the most demanding conditions.His mount does not allow the red dot to be co-witnessed with the iron sights. His mount puts the red dot 2. Reader: Please help! Please thanks! If sight can be co-witnessed then simply zero it to that distance.

Using wolf fmj grain. The iron sites are zero in by using your website! Then meters and rear setting back to 1.

But I always use battle setting! Bullets are grain wolf fmj thanks!! Using 7. I used yards for both. This zero will provide a trajectory that never rises above or below the height of the front sight from the muzzle out to yards.

As you can see from the numbers below, you rounds will impact within or very close to the red dot from about 25 yards out to almost yards. Excellent post! Thanks for more great information. I assume that having a red-dot with a slightly larger MOA i. Like Like. Great article. This is excellent information.

The only difference is the relative size of the dot at any given distance. At a particular distance the round might theoretically impact on the bottom or top edge of a 2 MOA dot, but still impact in the slightly larger 3 MOA dot. There is significantly more red dot area for the round to impact in.

Like Liked by 1 person.

Where to Mount Your Red Dot Sight

For red dot zeroing would you recommend a 25 yard point of aim point of impact? Also, is the height of my red dot irrelevant in relation to the height of my irons? Awesome question.


thoughts on “Micro draco red dot

Leave a Reply

Your email address will not be published. Required fields are marked *